Planing small boards?

[Rick Moreton]

I'd rather buy Harbor Freight than WoodRiver. Jokes aside, my lack of confidence in WoodRiver stems from to two sets of forstner bits that would not cut AT ALL. Horrible product. I switched to Fisch Wavecutters and they are amazing (albeit 3 times the money). In fairness, I do have a WoodRiver round scraper that seems OK.

I started with a Harbor Freight #4 which is now a dedicated scrub plane. It isn't fit for much else, sole was nowhere near flat, chip breaker was messed up, blade couldn't hold a decent edge, etc. I only might recommend it for someone afraid of catastrophically messing up restoring a vintage plane. I have a WoodRiver 5 1/2 and have no issues with it, I actually don't remember the last time I sharpened. I also have a set of forstner bits from WoodRiver and they are hit and miss. One bit cuts like butter and another is a pain in the butt.

On the flip side, I have many other Harbor Freight items including my lathe which works well.

 

[Steve Tiedman]

Paul Sellers, prepping flat boards'

View: https://youtu.be/m231_HKCOWs?si=fgdDT-wX-PX1xXbs

(While there, search his "The Three Joints" videos (3 separate videos), showing how to cut dovetails, mortise and tenon, and dado joints, all with basic hand tools.)

Christopher Schwarz, same-

View: https://m.youtube.com/watch?v=2_96gNMMc_g


Mike Siemsen, same-

View: https://m.youtube.com/watch?v=oEdgF8NDsB0


3 different authoritative sources showing time honored methods to prep flat boards with basic, classic handtools and methods.

Flattening with power tools, a jointer is first used to establish one flat surface, and then a powered planer or drum sander will use that flat surface (face down on the bed) as a reference to flatten the other surface parallel. A power planer or drum sander alone, with no jointer used first, will make it tough to get parallel face surfaces. But, a couple hand planes (#4 and maybe a #5 for somewhat larger boards) and 2 winding sticks, and a bit of practice, can create flat boards with parallel faces for much less money, noise, and equipment footprint vs. electric machines. And for smaller work, like display or presentation boxes, hand work has my vote over machines. Just takes some practice, and sharp blades.

 

[Doug Rasmussen]

Not knowing exactly what equipment Jon (the OP) currently has it's hard to make a recommendation. Most wood comes as either nominally 3/4" smooth planed or 1"+ rough sawn. So how do you get down to the desired 1/4" thick? A hand plane certainly doesn't sound like a good way to be removing 1/2" of material.

If my project was smallish boxes I might want highly figured wood. My experience with my 12 Powermatic planer highly figured wood didn't plane well with it's changing grain directions. Birds eye maple would chip out at the eyes. When we started doing lots of figured wood I bought the narrowest Italian thickness belt sander I could find. That sander would chew right through the worst wood with no issues. The thought of hand planing doesn't appeal to me.

I mentioned before using a hand held router to surface boards like the slab table makers do. That's a well proven way with a homemade jig setup. A similar method can be done on a table saw by supporting the blank on both edges and running over a dado blade. With both these methods final finish can be achieved with light scraping and/or sanding.

Investing in hand planes would be so far down on the list of possible methods it wouldn't even be a consideration for me.

 

[Gerald Lawrence]

Do not remember what I started with but probably a Craftsman used #5. Not the worst but not good. Most of what I have are Stanley Baileys. The blade you have makes a difference too I have a Hock in a #8 and a Pinnacle in a #7. it really made a difference. I did not read everything but Ron Hocks book is a good reference. Oh and I now have 28 planes of all sorts and yes a few are antiques but useable.

 

[Jon Rista]

I'd rather buy Harbor Freight than WoodRiver. Jokes aside, my lack of confidence in WoodRiver stems from to two sets of forstner bits that would not cut AT ALL. Horrible product. I switched to Fisch Wavecutters and they are amazing (albeit 3 times the money). In fairness, I do have a WoodRiver round scraper that seems OK.

I had a similar experience. WoodRiver forstners that either would NOT cut, or if they did, they burnt the wood in seconds. I switched to Fisch Wavecutters and I've never looked back. Vastly superior product, cuts wood like its butter, no problems ever.

My general problem with WR is the products aren't that great, but they are very expensive. If they had the quality, the price wouldn't necessarily be a problem, but the quality is usually not really there, and the prices seem extreme.

 

[Jon Rista]

Not knowing exactly what equipment Jon (the OP) currently has it's hard to make a recommendation. Most wood comes as either nominally 3/4" smooth planed or 1"+ rough sawn. So how do you get down to the desired 1/4" thick? A hand plane certainly doesn't sound like a good way to be removing 1/2" of material.

If my project was smallish boxes I might want highly figured wood. My experience with my 12 Powermatic planer highly figured wood didn't plane well with it's changing grain directions. Birds eye maple would chip out at the eyes. When we started doing lots of figured wood I bought the narrowest Italian thickness belt sander I could find. That sander would chew right through the worst wood with no issues. The thought of hand planing doesn't appeal to me.

I mentioned before using a hand held router to surface boards like the slab table makers do. That's a well proven way with a homemade jig setup. A similar method can be done on a table saw by supporting the blank on both edges and running over a dado blade. With both these methods final finish can be achieved with light scraping and/or sanding.

Investing in hand planes would be so far down on the list of possible methods it wouldn't even be a consideration for me.

The local woodcraft has small dimensional wood. Lots of exotics, like ebonies, rosewoods, various colored woods (redheart, yellowheart, osage orange, etc.) They have pieces usually 2-4 feet long, 2-4 inches wide, anywhere from 1/2" thick down to 1/16th in some cases. I have...I guess its mostly 2 foot long 2-3" wide, an 1/4" or 1/8" thick. So I don't necessarily have to plane the boards to thickness. My main interest was hand planing to smooth, as the boards are often not smooth...with clear snipes, waviness, etc. that are characteristic effects of rapidly shoving tons of boards into a thickness planer without a lot of care. 🤷‍♂️

I have one router...its big, bulky, and not easy to use handheld. I am not particularly proficient at it, and I am wary of using it on thin stock, say 1/8" thick? I mean, the stock is already flat, it just doesn't necessarily have a nice clean surface, and occasionally one end is a bit warped. I usually try to pick boards with two key characteristics: great grain, and minimal to no warping. I've had a couple of these pieces for close to a year (or maybe over a year now), and they must not have been 100% dry, as they are very slightly warped in some places. But for the most part, most of these boards are small, flat, and pretty much ready...they usually just have kind of a janky surface quality. Certainly not the kind I'd want to use in a product I would sell.

I can get some photos to show what I'm talking about, and why I was thinking hand planing was probably the best way to deal with the issue.

 

[Don Wattenhofer]

So I don't necessarily have to plane the boards to thickness. My main interest was hand planing to smooth, as the boards are often not smooth...with clear snipes, waviness, etc. that are characteristic effects of rapidly shoving tons of boards into a thickness planer without a lot of care. 🤷‍♂️

A card scraper will remove those waves or hand sanding would also work.
Stanley made a "cabinet scraper" which had 2 handles, a sole plate, clamps to hold the blade and a thumb screw to bend the blade into the work. Lee Valley has a similar cabinet scraper listed in their on line catalog.

 

[John K Jordan]

A card scraper will remove those waves or hand sanding would also work.
Stanley made a "cabinet scraper" which had 2 handles, a sole plate, clamps to hold the blade and a thumb screw to bend the blade into the work. Lee Valley has a similar cabinet scraper listed in their on line catalog.

I second that suggestion. I have the Veritas version and have sharpened the scraper and handed it to people who have never touched a scraper before. One of my sons resurfaced a butcher block table with it after 30 seconds of instruction.

JKJ

 

[Don Wattenhofer]

One of my sons resurfaced a butcher block table with it after 30 seconds of instruction.

That is the beauty of a burred scraper (cabinet scrapper or card scraper) it will cut thru the the grease and crud where as sandpaper will gum up and stop cutting.

 

[Jon Rista]

A card scraper will remove those waves or hand sanding would also work.
Stanley made a "cabinet scraper" which had 2 handles, a sole plate, clamps to hold the blade and a thumb screw to bend the blade into the work. Lee Valley has a similar cabinet scraper listed in their on line catalog.

I second that suggestion. I have the Veritas version and have sharpened the scraper and handed it to people who have never touched a scraper before. One of my sons resurfaced a butcher block table with it after 30 seconds of instruction.

JKJ

That is the beauty of a burred scraper (cabinet scrapper or card scraper) it will cut thru the the grease and crud where as sandpaper will gum up and stop cutting.

I actually have a set of scrapers... I forgot about them, but, I guess I can give them a try. Some of the boards, though, have enough sniping and other damage done to the surface, that I don't think a scraper will do the job. I have been reworking my Etsy store today, and I haven't gotten photos of the boards that have issues. I'll try to do that shortly here.

 

[Jon Rista]

Paul Sellers, prepping flat boards'

View: https://youtu.be/m231_HKCOWs?si=fgdDT-wX-PX1xXbs

(While there, search his "The Three Joints" videos (3 separate videos), showing how to cut dovetails, mortise and tenon, and dado joints, all with basic hand tools.)

Christopher Schwarz, same-

View: https://m.youtube.com/watch?v=2_96gNMMc_g


Mike Siemsen, same-

View: https://m.youtube.com/watch?v=oEdgF8NDsB0


3 different authoritative sources showing time honored methods to prep flat boards with basic, classic handtools and methods.

Flattening with power tools, a jointer is first used to establish one flat surface, and then a powered planer or drum sander will use that flat surface (face down on the bed) as a reference to flatten the other surface parallel. A power planer or drum sander alone, with no jointer used first, will make it tough to get parallel face surfaces. But, a couple hand planes (#4 and maybe a #5 for somewhat larger boards) and 2 winding sticks, and a bit of practice, can create flat boards with parallel faces for much less money, noise, and equipment footprint vs. electric machines. And for smaller work, like display or presentation boxes, hand work has my vote over machines. Just takes some practice, and sharp blades.

Thank you so much! I think you understood the "assignment" best! Your last paragraph pretty much summed up my goal...to do it by hand, to learn some new woodworking skills, and to not spend a lot of money. I'd LOVE to have all the machines...I am a fan of machines, but they just aren't in the budget right now.

Plus, I am looking forward to learning some classic woodworking skills. I really want to learn how to hand plane, even if its harder, not as efficient, not as fast, etc. Its a classic skill, and I really love the design of hand planes, so I'm quite looking forward to this little adventure.

 

[Jon Rista]

If my project was smallish boxes I might want highly figured wood.

Investing in hand planes would be so far down on the list of possible methods it wouldn't even be a consideration for me.

So, if you already had wood of the right dimensions...where you did not have to remove significant amounts of wood with a hand planer, but instead only had to smooth out and level the boards you had... Would you use a hand plane? The boards I have do have good grain and sometimes figure (awesome figure hasn't been easy to find in these pre-sized boards...photos coming shortly here.) But, most DO have nice grain in general. Now, some don't necessarily, but, I was also thinking I'd use some of these first to get the hang of things, as I'll undoubtedly screw the first couple or so up in some way. So I wasn't really looking for the most exquisite wood either. I figure if I really wanted a truly EXQUISITE grain, I could probably work with some veneer...that's another skill I do not have, but I do know that I could probably veneer PHENOMENAL grain onto a more basic wood if I wanted something that really popped. I know veneering is a whole different ball of wax, and its not what I'm looking to do right now...

Anyway. FWIW, and I know I mentioned this in my previous reply, the boards are really already sized. They just need to be cleaned up. I could sand...but so many people have told me that hand planing will deliver a better surface than sanding, period, and in my limited experience so far, I can see why they say that. I won't need to plane off half an inch of material. I suspect for the most part, 1/32nd is probably the most I'd ever need to plane off, more likely a 64th or 128th on boards that are already in pretty good shape? I assume a hand plane would work well for that, right?