This is the other side of a dicey piece of mulberry I previously turned.
-
Beware of Counterfeit Woodturning Tools (click here for details) -
Johnathan Silwones is starting a new AAW chapter, Southern Alleghenies Woodturners, in Johnstown, PA. (click here for details) -
Congratulations to Rabea Gebler for "Plum Blossom" being selected as Turning of the Week for June 24, 2024 (click here for details) -
Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.
Would You Turn This?
- Thread starter Kent Reisdorph
- Start date
It will take a lot of sanding. Hard (for me) to get a smooth cut with that big void.
Should finish it today.
Should finish it today.
I would take a piece like that and donate it to the club wood raffle. I could turn it, but wouldn't want to since I prefer daily use pieces rather than art. An interesting piece of wood.
robo hippy
robo hippy
Looks like a piece of wood that could hurt you badly.
Will definitely be an art piece unless you do a lot of epoxy work. I've only turned a few pieces of mulberry but my experience and what I'm told is expect a lot of cracks and movement if it was green/wet when turned.
Would I turn it? Probably not.
Could I turn it? Yes. I would do it on my CNC mill to minimize any needed sanding. I've used various ways to mechanically stabilize fragile pieces. Bondo auto body filler works well using Saran wrap liner so it doesn't stick to the wood. Also wax granules melted to fill and stabilize.
Why are you turning it? Sometimes pieces like this are shown, my thought is they were done as a personal challenge or to demonstrate the turner's skill. Most everything I turn is utilitarian and if it happens to be attractive that's even better. A bowl with a void in the side wouldn't be utilitarian.
Could I turn it? Yes. I would do it on my CNC mill to minimize any needed sanding. I've used various ways to mechanically stabilize fragile pieces. Bondo auto body filler works well using Saran wrap liner so it doesn't stick to the wood. Also wax granules melted to fill and stabilize.
Why are you turning it? Sometimes pieces like this are shown, my thought is they were done as a personal challenge or to demonstrate the turner's skill. Most everything I turn is utilitarian and if it happens to be attractive that's even better. A bowl with a void in the side wouldn't be utilitarian.
Yes, it cracks pretty easily when green.
Definitely for the challenge. I don't do art, per se. Will it be functional with a large void? No, but I'll still like it.
probably not but if I had, I’d have used every screw hole in a larger faceplate to minimize the chance of an airborne chunk.
Just don't use it for soup and it will be fine
It's the only faceplate I have (I don't use them often). I think I got 5 screws in it. There wasn't any way to position it so that all of the screw holes were over solid wood.
Would I turn that?? That's all I turn, all day, every day!
Great chunk of wood! Tons of potential and I look forward to seeing the final product.
Great chunk of wood! Tons of potential and I look forward to seeing the final product.
Would turn it after looking it over very well. I would probably put a 5" or 6" glue block on it and then attach my faceplate to that. Then do the tenon like you did.
I should have thought of a glue block.
Fire wood
Finished. Shellac base, Tried and True Original finish. Soup eaters need not apply.
Striking, Kent. Nice work!!
Turned out nice Kent
Souper cool! Well done, and nice save of a piece of wood that very few would be willing to turn.
I would 100% turn that! Living in a place like where I do, I can't be picky with the wood I can turn, so if I want to turn, I turn sketchy chunks. Along with that, what techniques do you use for turning pieces with voids or that are out of balance? For hollow forms or bowls, do you increase the speed, decrease the speed, or what do you do with your tool to avoid catastrophe? Great Job!
Start slow. This is especially important for uneven blanks.
As for turning wood with a lot of voids, the key is in knowing (or accurately guessing) how stable the wood is around the voids. In this case it was pretty stable so there wasn't much risk of it coming apart. The other thing to watch for when turning live edge or wood with voids is to not push the gouge into the wood. If you are pushing forward on the gouge, when you hit air the gouge will go into the void, and then smack the wood on the other side of the void. This happens in small increments, but it's a thing. Try to use as little forward pressure on the gouge as possible. I have to remind myself of this constantly.
As for turning wood with a lot of voids, the key is in knowing (or accurately guessing) how stable the wood is around the voids. In this case it was pretty stable so there wasn't much risk of it coming apart. The other thing to watch for when turning live edge or wood with voids is to not push the gouge into the wood. If you are pushing forward on the gouge, when you hit air the gouge will go into the void, and then smack the wood on the other side of the void. This happens in small increments, but it's a thing. Try to use as little forward pressure on the gouge as possible. I have to remind myself of this constantly.
Kent - Your piece is totally non-functional which is, to my thinking, a compliment. If displayed alongside bowls that are "functional", your piece will get the attention.
Good job
Good job
Absolutely, I love this sort of challenge. Although Mulberry, where I live is very drab and not exactly inspiring and I dont see much of it.
Wow, a beautiful result
Nice piece, Kent! I like the little piece of void on the far side, too. Great addition to any countertop or shelf 👍🏻
I credit the ants.
That came out beautifully @Kent Reisdorph