• November Turning Challenge: Puahala Calabash! (click here for details)
  • Sign up for the AAW Forum Pre-Holiday Swap by Monday, November 4th (click here for details)
  • Congratulations to Nino G. Cocchiarella for "Woven Seat Stool" being selected as Turning of the Week for October 28, 2024 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.
Pierced sycamore bowl
Bread Platter
Emerging Vase
Yo-Yo lidded box
Pierced sycamore bowl
Kingwood Lidded Box
Pyinma Catch All
Pyinma Catch All
Lou Jacobs

Pierced sycamore bowl

6 1/4” x 2 1/2” bowl. The area of the piercing is a bit under 1/8” thick. My first effort at this kind of decoration.
Click to expand...
  • Like
Reactions: Ted Pelfrey, Dimitris Psilopatis, Todd A Williams and 14 others
Lou Jacobs
Absolutely Russ. I was a bit surprised how much effort it took for the burrs to cut through. Next attempt, I’ll go for a smidge thinner.
 
Lou Jacobs
I just looked it up. You mean the entire hand piece/motor? I have a Marathon micro motor tool that was my fathers. He was a wood carver and used it for detailing his carvings. I inherited it when he died about 13 years ago and I’ve never used it before this week. Only problem is it has a 3/32 inch collet and I’m not sure if or how to change it to an 1/8” inch collet. All the burrs that he had with it were fine diamond burrs for carving details like feathers etc. I’d like to be able to accommodate 1/8 inch shank Saburrtooth and other carbide burrs. But so far I can’t figure out how to change the collet.
 
Russ Braun
Lou Jacobs said:
I just looked it up. You mean the entire hand piece/motor? I have a Marathon micro motor tool that was my fathers. He was a wood carver and used it for detailing his carvings. I inherited it when he died about 13 years ago and I’ve never used it before this week. Only problem is it has a 3/32 inch collet and I’m not sure if or how to change it to an 1/8” inch collet. All the burrs that he had with it were fine diamond burrs for carving details like feathers etc. I’d like to be able to accommodate 1/8 inch shank Saburrtooth and other carbide burrs. But so far I can’t figure out how to change the collet.
Click to expand...
Some older micro motor handpieces have the collet thread in, this 3/32 might just unscrew. NSK Presto is an air driven tool; 300K plus rpm; it is like a dental tool. The only way to pierce!!
 
Tom Gall
Nice first attempt, Lou. 1/8" thick can be a tough go - probably the cause for your uneven top and bottom borders. For your next one - draw or incise your border lines and cut/pierce short of the lines, then sand flat to the line with small sandpaper stick or emery board. A lot of extra work but probably worth it.
 

Media information

Category
Member Galleries
Added by
Lou Jacobs
Date added
View count
818
Comment count
6
Rating
0.00 star(s) 0 ratings

Image metadata

Device
Apple iPad mini 4
Aperture
ƒ/2.4
Focal length
3.3 mm
Exposure time
1/20 second(s)
ISO
200
Filename
ED9D3111-E51F-49F6-AB18-AD6046E19BA5.jpeg
File size
1.1 MB
Date taken
Sun, 09 July 2023 2:44 PM
Dimensions
2448px x 2448px

Share this media

Back
Top