1. Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

Search Results

Search Again
Page 1 of 7
  1. Jake Debski
    Post

    Grinder dust collection

    John, FWIW department, a good friend and very active turner I know has a 7" Baldor grinder. He rubber bands cotton socks to the outlet ports. He...
    Post by: Jake Debski, Dec 29, 2011 in forum: Woodturning Discussion Forum
  2. Jake Debski
    Post

    OT One Mystery Solved

    MM, this is not uncommon with Cardinals and house windows here. Must admit attacking the car windows is a new one though.
    Post by: Jake Debski, Apr 22, 2011 in forum: Woodturning Discussion Forum
  3. Jake Debski
    Post

    A question for John Lucas.

    Thanks to all......... for your responses. John, your video is just what the doctor ordered, thank you.
    Post by: Jake Debski, Apr 21, 2011 in forum: Woodturning Discussion Forum
  4. Jake Debski
    Thread

    A question for John Lucas.

    John, on a few past occasions you posted photos of set up tools you cut from plywood to set the distance of the "v" arm from the face of the...
    Thread by: Jake Debski, Apr 20, 2011, 5 replies, in forum: Woodturning Discussion Forum
  5. Jake Debski
    Post

    Sharpening Skews

    Jimmy Clews, also is a proponent of such a grind. During a demo/hands on a few years ago he explained his reasoning behind grinding a skew that...
    Post by: Jake Debski, Apr 10, 2011 in forum: Woodturning Discussion Forum
  6. Jake Debski
    Post

    The New Bylaws

    I have always maintained "you have the best possible solution, under the circumstances, when neither side is totally satisfied." The volunteer...
    Post by: Jake Debski, Apr 6, 2011 in forum: AAW Information
  7. Jake Debski
    Post

    "Choice Woods National Woodturning Championship"

    Hats off to both entrants, and Kudos to Keith.
    Post by: Jake Debski, Apr 5, 2011 in forum: Woodturning Discussion Forum
  8. Jake Debski
    Post

    gouge profile diagram

    Patrick, Its important to remember flute profiles vary by manufacturer. The flute dictates the profile when grinding. So any "quick guide" is...
    Post by: Jake Debski, Apr 3, 2011 in forum: Tutorials and Tips
  9. Jake Debski
    Post

    Can you harden maple by sanding too vigorously?

    Frans, it sounds as though you created enough heat to produce case hardening of the surface. When it comes to turning wood, excessive heat heat is...
    Post by: Jake Debski, Apr 2, 2011 in forum: Woodturning Discussion Forum
  10. Jake Debski
    Post

    The New Bylaws

    Sadly, you are spot on. One more thing to consider, did all of our back and forth angst turn off such a large number of otherwise interested...
    Post by: Jake Debski, Apr 2, 2011 in forum: AAW Information
  11. Jake Debski
    Post

    PM 3520 bed extension alignment

    Walt, First I do not have the bed extension on my 35-20. I have a question which you probably may or my not of thought about. Did you loosely...
    Post by: Jake Debski, Mar 30, 2011 in forum: Woodturning Discussion Forum
  12. Jake Debski
    Post

    AAW March 2011 Contest

    Kudos to Robert Manning, and the runners up. The creative energy displayed in all the entries speaks well of the enormous talent and vision spread...
    Post by: Jake Debski, Mar 25, 2011 in forum: Woodturning Discussion Forum
  13. Jake Debski
    Post

    delta lathe dis and reassembly

    Bill, Its(Delta) been sold again, to a company based in Taiwan. The B.D., Dewalt, Stanley Group still is supposed to do service work. Like...
    Post by: Jake Debski, Mar 20, 2011 in forum: Woodturning Discussion Forum
  14. Jake Debski
    Post

    PM 3520b Owners

    I also have a two pole disconnect switch and I unplug after finishing a session. Like Scott, I have had lightening damage in the past, so why risk it.
    Post by: Jake Debski, Mar 10, 2011 in forum: Woodturning Discussion Forum
  15. Jake Debski
    Post

    4 Jaw 6" Chuck For Old Lathe

    Greg, There are much better penetrating products than WD-40, which was actually developed as a water displacement oil. PB Blaster is one that...
    Post by: Jake Debski, Feb 16, 2011 in forum: Woodturning Discussion Forum
  16. Jake Debski
    Post

    4 Jaw 6" Chuck For Old Lathe

    Greg to speed up the action of the WD-40 lift the Headstock end so that the penetrant flows toward the spur-drive. That will help keep more of it...
    Post by: Jake Debski, Feb 15, 2011 in forum: Woodturning Discussion Forum
  17. Jake Debski
    Post

    Life span of diamond hone?

    Odie if you have the Winter-2008 AAW Journal it is there by Alan Lacer. It is also on his website http://www.alanlacer.com/ It is not...
    Post by: Jake Debski, Feb 13, 2011 in forum: Woodturning Discussion Forum
  18. Jake Debski
    Post

    Threading Jig

    Thanks John,I am looking forward to the article.
    Post by: Jake Debski, Feb 13, 2011 in forum: Woodturning Discussion Forum
  19. Jake Debski
    Post

    Life span of diamond hone?

    Scraper burr Odie, Late fall of 2010 I attended a hands on given by Al Stirt, at the Presque Isle Turning Club, in Erie,PA. Of all the...
    Post by: Jake Debski, Feb 13, 2011 in forum: Woodturning Discussion Forum
  20. Jake Debski
    Post

    Sad news today

    Kelly, excellent question, I doubt there are few "one size fits all" answers. One group I belong to, for the past 8 or 9 years, is constantly in...
    Post by: Jake Debski, Feb 13, 2011 in forum: AAW Information
Showing results 1 to 20 of 128 Next >
Search Again
Page 1 of 7
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice