• Beware of Counterfeit Woodturning Tools (click here for details)
  • Johnathan Silwones is starting a new AAW chapter, Southern Alleghenies Woodturners, in Johnstown, PA. (click here for details)
  • Congratulations to Paul May for "Checkerboard (ver 3.0)" being selected as Turning of the Week for March 25, 2024 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

Making buttons - need advice

Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
I’m making some large buttons for my daughter who is knitting a sweater. I wonder if anyone has experience or thoughts about a good finish that may stand up to periodic cleaning, or is that simply impossible? Also, grain orientation. While I like this look, I wonder if making them parallel to the grain (flat-grained) might offer less opportunity for water being absorbed. This one is ash, but I imagine an oilier wood like teak, rosewood, etc., might be a better choice.
56E4C985-13E5-46D3-9008-6527D3ED4B71.jpeg
 
Joined
Jan 22, 2009
Messages
441
Likes
678
Location
Crossville, TN
I built a cedar strip canoe that saw lots of water. It used thin epoxy (West Systems) soaked into the wood and fiberglass, then had spar varnish over that for UV protection.

if it were me, I think I’d saturate the buttons in epoxy (NOT 5minute type).
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Interesting idea Ron. I’ve also built several cedar strip, and also stitch and glue boats. (See my avatar, in one of my Adirondack guideboats). I hadn’t thought about epoxy and varnish, as I didn’t want that glossy a finish, but it is worth a try. Honestly, it had not crossed my mind. I have half a gallon of MAS epoxy and various hardeners on the shelf. Thanks for the suggestion!
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
I have pondered doing buttons and always wondered if I should go flat grain or end grain. I was thinking flat grain would be more crack resistant. No clue as to finish, but carnuba wax or micro crystaline would be safe...

robo hippy
 
Joined
Jul 17, 2010
Messages
108
Likes
40
Location
Waco, TX
Might be a good argument for some cactus juice!
I love wooden buttons they are the perfect finish to a hand made garment
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Interesting thought Dean. I have no experience with it. Is a vacuum chamber and pump necessary? Nothing like spending a couple hundred bucks to be able to make a $2 piece.
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
I am out in the middle of the valley, so other than smoke and ash, I am fine. Oh, the swimming pool closed again, and the Farmer's Market closed. Supposed to be some rain moving in Monday. I have had one friend that lost his house, and several others that had to evacuate, but thus far, their homes are okay. Rough times for sure.

robo hippy
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Gary, thanks for that suggestion. I’ve got a couple that I put epoxy on a few hours ago. I’ll try your CA idea too.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
I would cut a piece of stock as if it were a very narrow bowl blank. Center of the tree at the headstock or tailstock (I don’t think it would matter much either way), and growth rings perpendicular to the axis of rotation. The way the buttons were made, as in post #1, it was cut from a spindle with growth rings parallel to the bed. Maybe a better way to put it is that the tree, before the blank is cut would be perpendicular to the bed. In the ones I cut the tree is parallel to the bed. I’ll try to do some tomorrow and post a picture.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
PS - I neglected to say that I’d mount the blank, as I did for the previous buttons, securely in a chuck just at the headstock and cut them off the end of the spindle, after first facing off the front of the button with a bowl gouge, sanding it smooth, then with a parting tool, cut most of the back of the button, sanding the back that I can reach, then finish parting it off. Sand the remaining nub with a disc mounted in the lathe or drill press, then drill holes for sewing the button.
 
Joined
Jul 19, 2018
Messages
1,688
Likes
2,079
Location
Ponsford, MN
Hey, let's back up a minute. Start to finish, how would you turn a wood button? (Flat grain).
Weather it is face grain or end grain would depend on the species since there are strength issues with both. The problem could be solved by making a plywood out of veneer or thin strips cut from the edge of a board. The flat blank cut roughly round can be held between a flat face jig in your headstock with sand paper on it and a live center with a flat face. Example for a 1" diameter button the drive end would be a block of wood turned down to 1/2" diameter with a flat end and sand paper glued on. The tail-stock live center would be fitted with a 1/4" diameter flat face. The blank can be sandwiched in without marking and the edges and a 3/8" donut will be exposed for turning the details. This is method that I have used to turn bottoms for shrink boxes without having any marks on them so I think it should work at the smaller scale to make buttons. I may try it
tomorrow Note to admin. when I miss spelled tomorrow and used spell check it shifted to a new line.
 

Emiliano Achaval

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Dec 14, 2015
Messages
3,307
Likes
4,226
Location
Maui, Hawaii
Website
hawaiiankoaturner.com
I am out in the middle of the valley, so other than smoke and ash, I am fine. Oh, the swimming pool closed again, and the Farmer's Market closed. Supposed to be some rain moving in Monday. I have had one friend that lost his house, and several others that had to evacuate, but thus far, their homes are okay. Rough times for sure.

robo hippy
Stay safe Reed!
 

Emiliano Achaval

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Dec 14, 2015
Messages
3,307
Likes
4,226
Location
Maui, Hawaii
Website
hawaiiankoaturner.com
I’m making some large buttons for my daughter who is knitting a sweater. I wonder if anyone has experience or thoughts about a good finish that may stand up to periodic cleaning, or is that simply impossible? Also, grain orientation. While I like this look, I wonder if making them parallel to the grain (flat-grained) might offer less opportunity for water being absorbed. This one is ash, but I imagine an oilier wood like teak, rosewood, etc., might be a better choice.
View attachment 34993
I would use something dense, side grain. Because I have it, Lignum Vitae would be perfect. You should try to clean up the torn grain before sanding your button, if you apply some finish that is going to be very noticeable.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
I would use something dense, side grain. Because I have it, Lignum Vitae would be perfect. You should try to clean up the torn grain before sanding your button, if you apply some finish that is going to be very noticeable.
Emiliano, of course you’re correct about the tear out. The one shown was only a prototype, but still no excuse to not be more careful with a smoother cut. I’d suspect Lignum Vitae might be oily enough to require no finish. I should look for some. In the meantime, I’ll experiment later today with some side grain ash and hard maple. I have a few pieces of ash with wide enough growth rings, that I might even be able to get some discs entirely out of the less porous summer wood section of the ring.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Hey, let's back up a minute. Start to finish, how would you turn a wood button? (Flat grain).
Tom, here’s what I did a few minutes ago:
Cut a cross grain piece off an ash slab, 2 1/2” x 2 1/2” by about 8”. Turn round between centers, then mount in scroll chuck, turn down to 1 3/4” diameter, and face off end with slight concavity. Sand face, then partially part off, sand, then finish parting. Drilling for thread and sanding the back is done on the drill press.
Not much springwood is visible, at least on the faces, and I believe these will be much stronger than cross grained buttons. I’m still trying to decide if I’ll apply a hard (epoxy or CA?) finish, or just oil them.
8147000B-EBA8-4182-A6B1-6C50AD815D54.jpeg 43753140-E134-4ACC-B090-3C6414D72D0D.jpeg 908298D7-B780-4B23-8A6C-9273E3373E26.jpeg 36AD9EA3-8978-4699-92FB-8E9D5E8C8278.jpeg 8CE0DAE9-D558-49FB-B9CE-8EB082B49523.jpeg
 
Joined
Sep 27, 2017
Messages
396
Likes
204
Location
Windsor, Pennsylvania
Years ago, when I did some re-enacting, my broadfall trousers had wooden buttons.. I believe, I was told they were sycamore. They were flat grained with four holes, and were perhaps an inch in diameter. They were treated with something, because I washed the trousers in the wash machine at least a dozen times before the buttons started to turn ugly. I replaced them with hand turned horn buttons that lasted just fine through years of washer and dryer abuse. The horn buttons were also cut flat grained. I cut them out with a plug cutter mounted in a drill press and going very slowly., then sanded them flat and mounted them on my metal lathe to drill holes, finish and polish.
 
Joined
Feb 8, 2014
Messages
1,173
Likes
611
Location
Evanston, IL USA
Tom, here’s what I did a few minutes ago:
Cut a cross grain piece off an ash slab, 2 1/2” x 2 1/2” by about 8”. Turn round between centers, then mount in scroll chuck, turn down to 1 3/4” diameter, and face off end with slight concavity. Sand face, then partially part off, sand, then finish parting. Drilling for thread and sanding the back is done on the drill press.
Not much springwood is visible, at least on the faces, and I believe these will be much stronger than cross grained buttons. I’m still trying to decide if I’ll apply a hard (epoxy or CA?) finish, or just oil them.
View attachment 35024 View attachment 35025 View attachment 35026 View attachment 35027 View attachment 35028

Thanks Lou!
 
Joined
Jul 19, 2018
Messages
1,688
Likes
2,079
Location
Ponsford, MN
I tried to describe a method I thought would work in a previous post so I decided to try it. The test buttons are 1" diameter and made form 3/16" thick material. The light colored one is a 3 ply plywood made of lilac and the darker one is face grain sorta from highly figured buckthorn. The drive is a block of maple turned down to a 1/2" diameter flat face with a disk of sandpaper glued on. The clamp or tail stock live center is a Nova live center with a custom made 1/4" flat face. The holes are drilled using one adjustment - the button is pressed into the block and drilled for the first hole then rotated 90 degrees for the second of 4 holes, 180 degrees for the second of 2 holes etc. The tool shown in picture 3 is a small round nose scraper made form a 8-32 HS broken tap and held with a vise grip, which makes an excellent handle. The 4th picture shows a small screw driver holding the button so that it does not lift out with the drill bit and the cross notches are there to pop the button out if it is a tight fit. The one problem is that you can't dish out the button unless you made a jam chuck for that operation.
Button1.jpg button2.jpg button3.jpg button4.jpg
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Don, everything about your process is exquisite! I love the small scraper you made. Perfect for the curve of the button face, and likewise the jig for drilling the four holes at perfect 90° opposition. I’m sure I’ll adopt some of your method as I’m already being asked for more buttons! I wonder how long before they justify the cost of the lathe...
 
Joined
Jul 19, 2018
Messages
1,688
Likes
2,079
Location
Ponsford, MN
Don, everything about your process is exquisite! I love the small scraper you made. Perfect for the curve of the button face, and likewise the jig for drilling the four holes at perfect 90° opposition. I’m sure I’ll adopt some of your method as I’m already being asked for more buttons! I wonder how long before they justify the cost of the lathe...
If you were worried about justifying the cost of the lathe you would not be doing it. It is nice to link up to another craft especially when it is your daughter.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Of course you’re right Don. The way I look at it, turning is cheaper than psychotherapy...well, maybe, maybe not! ;-)
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
I’d love to Dave. Am I correct that it requires a vacuum pump and chamber? I don’t have them right now, but would love to put together a vacuum chuck, so that would just further help justify the purchase.
 

Tom Gall

TOTW Team
Joined
Feb 20, 2013
Messages
956
Likes
1,765
Location
Hillsborough, NJ
I’d love to Dave. Am I correct that it requires a vacuum pump and chamber? I don’t have them right now, but would love to put together a vacuum chuck, so that would just further help justify the purchase.
You can try using Minwax Wood Hardener. Submerge blanks in a cat food/tuna fish can until air bubbles stop - let dry (overnight) - then turn. No vacuum pump or chamber needed! Hardener is reusable.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
You can try using Minwax Wood Hardener. Submerge blanks in a cat food/tuna fish can until air bubbles stop - let dry (overnight) - then turn. No vacuum pump or chamber needed! Hardener is reusable.
Tom, no excuse to buy a vacuum chuck, at least for this project? Shucks!
Seriously, I’m not familiar with the product, but will look into it. Thanks loads!
I’ve already put a few coats of Danish oil on these latest buttons, and am liking how they look. Yet to be seen how they stand up to wear.
 
Joined
Jul 18, 2018
Messages
1,061
Likes
1,719
Location
Baltimore, MD
Careful, I’m a retired psychotherapist! But I did have more than one client who I tried to convince that taking up something like turning or pottery would be more therapeutic than seeing me.
 
Back
Top