• Beware of Counterfeit Woodturning Tools (click here for details)
  • Johnathan Silwones is starting a new AAW chapter, Southern Alleghenies Woodturners, in Johnstown, PA. (click here for details)
  • Congratulations to Paul May for "Checkerboard (ver 3.0)" being selected as Turning of the Week for March 25, 2024 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

Signing Bowls?

Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Just wondering if anyone uses a wood burning pen to sign bowls. I have used sharpies, bought a wood burning iron with signature, and currently use dremel engraver, then I stain the engraving. If the bottom isn’t perfectly flat, the iron rocks and doesn’t look good. The sharpies run and wear off. And the engraver works ok, but you have to then put stain in it to make it show. Just thought a wood burning pen might work. Thanks
 
Joined
Nov 4, 2011
Messages
495
Likes
744
Location
Bay Settlement, WI
I keep a Colwood Cub woodburner with a writing tip in the shop to sign bowls, etc. I also have an electric branding iron, but it requires a pretty flat surface or it produces irregular results (I used the branding iron on flat work before I started turning ... it doesn't get much use now!).
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Scorch pen looks neat but I guess I was more thinking of a simple wood burning pen that you could hold good enough to sign with. Thanks for replies.
 

hockenbery

Forum MVP
Beta Tester
TOTW Team
Joined
Apr 27, 2004
Messages
8,590
Likes
4,885
Location
Lakeland, Florida
Website
www.hockenberywoodturning.com
A great many turners sign with a wood burning tip.
What generally works best is a small ball or rounded wire tip as they move easily in all directions.
Experiment with speed and temperature.
Generally a slow writing speed and med low temperature works best.

I find wearing optivisors ( magnifying lenses) helps too.
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
I found a Chandler wood burner with good reviews. It looked small and simple to use.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,884
Likes
5,168
Location
Dalworthington Gardens, TX
Website
pbase.com
Joined
Oct 13, 2016
Messages
1,053
Likes
1,463
Location
Rainy River District Ontario Canada
I have been using a pyrography burning pen to sign my turnings for a long time, it works well, though some woods are harder to write on than others, slow and steady works best for me.

Here are some that show how I sign and also the burner and pens that go with it, there all kinds of pens, a “writing” tip works best and what I use, Lee Valley is one of the places that sell the pens and burners.
https://www.leevalley.com/en-ca/shop/tools/power-tools/31042-the-razertip-wood-burning-systems


Bottoms 1.jpg bottoms 2.jpg Burners and pens.jpg
 
Last edited:
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Thanks a lot. That was the one and that was kind of my thoughts but saw some example stuff and thought it might work. Thanks for the photos. Looks like some nice work and burner works well.
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
I looked at the pjl website. Looks like they have ball point in 19 s- l. Which would be best. Thanks
 
Joined
Apr 20, 2006
Messages
1,265
Likes
992
Location
Erie, PA
I use a Pigma Micron Pen, archival ink that does not smudge. I have not found a finish that bothers it.
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Thanks again for all the help.
 
Joined
Jun 29, 2017
Messages
799
Likes
562
Location
Jasper, Alabama
I use a Optima woodburning pen as well to sign my work. It is very easy to control and you can adjust the heat as well.
 
Joined
Feb 26, 2019
Messages
1,813
Likes
1,415
Location
Lebanon, Missouri
Another option is an engraver. I've seen quite a few turners use them, as do I. I use this one from Dremel, less than $30 https://www.dremel.com/en_US/products/-/show-product/tools/290-engraver-kit. I use a black pen to write whatever, then go over that with the engraver. Versus a burner the wood is indented and more difficult to remove, not sure if that is an advantage or not. I've considered a burner, but I don't think it saves me time - I would need to use pen/pencil to write with, then trace with a burner, probably about the same time. If one can "sign" with a burner without tracing it out it saves time.

One advantage of an engraver is marking on metals - I use it to put various markings on tools and such, it will mark hardened tool steel.
 

Timothy Allen

Beta Tester
Beta Tester
Joined
Sep 11, 2019
Messages
212
Likes
148
Location
Maine
A simple soldering iron with a chisel tip can be used to burn basic block lettering....

(Edit: I a should have written this out in all caps..... ;-)
 
Joined
Feb 16, 2012
Messages
193
Likes
815
Location
Sebastopol, California
I have used a Colwood Detailer woodburner for many years for signing my pieces, and I use the RT-C tip (https://woodburning.com/collections/replaceable-tips-rt) for anything that involves handwriting. On my pieces with a milk paint finish or very finely polished surfaces, I use an inexpensive engraver.
The title on the musical plate was done with the RT-C tip, as an example...
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Thanks for the photo and all the advice. You all have given me plenty options.
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
I have that engraver, just doesn’t show up good on some woods. So I always put stain in the engraving and sometimes it bleeds and doesn’t look too good. So I thought burning might be simpler. I just scratch it out with the engraver. I guess using a pencil might make it neater. Thanks again
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
I’m guessing you burn the wood before finishing or buffing. Is that correct?
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Thanks
 

Emiliano Achaval

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Dec 14, 2015
Messages
3,307
Likes
4,224
Location
Maui, Hawaii
Website
hawaiiankoaturner.com
There have been several threads about this same topic. I know, I started one a few years ago. I wanted to buy a branding iron. I ended up using my Dremel engraver, like Betty Scarpino. On some work I rub a gold wax pen that Cindy Drozda sells, then I spray lacquer. Looks very classy. You might want to search for the older threads. Aloha
 
Joined
Feb 6, 2010
Messages
2,959
Likes
1,905
Location
Brandon, MS
Have used two methods till recently. Sign with pyrograpgy and place logo in center with bit I made to achieve 3 interlocked circled. I looked on Etsy and found branding irons for $27 from China and takes a month almost exactly. The first I ordered 1 inch and it was 1 inch wide but 1.5 tall so I ordered a 1/5 inch and it works great.Images are deceiving but the first is the larger iron IMG_3871.jpg IMG_3968.JPG
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
Thanks a lot for the pics and info. I’ll look at the other threads.
 
Joined
Feb 13, 2012
Messages
20
Likes
1
Location
Pineville, KY
I appreciate all the help. I ended ordering an Optima 1. It seems to work great. First time I’ve used a woodblock. Thanks again.
 

RichColvin

Super Moderator
Staff member
OTI Member
Joined
Mar 13, 2016
Messages
667
Likes
497
Location
Marysville, OH
Website
www.colvintools.com
Another option is an engraver. I've seen quite a few turners use them, as do I. I use this one from Dremel, less than $30 https://www.dremel.com/en_US/products/-/show-product/tools/290-engraver-kit. I use a black pen to write whatever, then go over that with the engraver. Versus a burner the wood is indented and more difficult to remove, not sure if that is an advantage or not. I've considered a burner, but I don't think it saves me time - I would need to use pen/pencil to write with, then trace with a burner, probably about the same time. If one can "sign" with a burner without tracing it out it saves time.

One advantage of an engraver is marking on metals - I use it to put various markings on tools and such, it will mark hardened tool steel.

What size and type of grinding tip do you use?
 
Back
Top